Driveway removal
Breaking and removing failed or unwanted concrete driveways, including haul-off and site cleanup before replacement or conversion to another surface.
Concrete removal and demolition in Missoula
Concrete removal is the first step in many replacement projects. We handle demolition, breaking, haul-off, and site cleanup so the property is ready for new concrete or another use.
Concrete removal can range from a small walkway panel to an entire driveway or foundation slab. The scope, equipment, haul-off, and cleanup vary by project size and site access.
Breaking and removing failed or unwanted concrete driveways, including haul-off and site cleanup before replacement or conversion to another surface.
Demolition and removal of patios, walkways, aprons, equipment pads, and flatwork slabs that are being replaced or eliminated.
Selective removal of failed sections, settled panels, or damaged concrete while preserving surrounding good concrete.
Removal of old foundation concrete, footings, stem walls, and basement slabs for renovation or new construction.
Estimate planning
Removal cost depends on the size of the area, the thickness and reinforcement in the concrete, site access, and haul-off distance. Simple tearouts are cheaper than complex demo jobs.
Larger areas and thicker slabs take more time to break and remove. Reinforced concrete with rebar or wire mesh is slower to demolish.
Tight spaces, side yards, and limited equipment access increase labor and slow down the work.
Disposal fees, dump distance, and load count affect the final cost. Disposal is included in most removal estimates.
Utilities, adjacent structures, landscaping protection, and saw-cutting around preserved areas add complexity and time.
Site conditions and project specifications determine final pricing.
Scope the cause first
Not every concrete project requires full removal. The decision depends on the condition of the existing slab, what caused it to fail, and what the replacement project requires.
The slab is severely cracked, settled, improperly graded, or structurally failed, and a new pour from the base up is the right solution.
Only certain sections have failed, and selective saw-cut removal and replacement make sense while preserving stable areas.
The existing concrete is structurally sound but cosmetically worn, and a bonded overlay or decorative surface may work instead of full removal.
Concrete removal in Missoula must account for site access, equipment constraints, utility locations, and disposal logistics. A clean removal sets up the replacement project correctly.
Tight yards, landscaping, fences, and gate width determine whether removal requires hand tools, a skid steer, or larger equipment.
Water lines, gas lines, electrical conduit, and septic systems are often near or under old concrete. Utility locates and careful digging protect existing infrastructure.
Broken concrete must be loaded, hauled, and disposed of properly. Disposal costs are part of the removal estimate.
Once old concrete is removed, the base and subgrade are exposed. This is the best time to assess whether drainage or base correction is needed before the replacement pour.
01
We review access, utilities, adjacent structures, landscaping, and what needs protection during removal.
02
Breaking can involve saws, jackhammers, excavators, or skid steers depending on thickness, reinforcement, and site access.
03
Broken concrete is loaded and hauled to an approved disposal or recycling facility.
04
The site is cleaned, graded, and ready for the next step, whether that is new concrete, gravel, landscaping, or another surface.
The strongest concrete projects are clear before the pour starts: scope, prep, drainage, finish, schedule, and maintenance all need to line up.
Utilities, landscaping, and adjacent structures are protected during demolition and haul-off.
The site is left clean, graded, and ready for the next phase of work without debris or trip hazards.
Removal exposes the subgrade and base, giving a clear picture of what needs correction before new concrete is poured.
We serve Missoula and nearby communities with concrete work planned around site conditions, access, drainage, and finish requirements.
Sometimes. Isolated damage or one failed panel can be a good candidate for section replacement when the surrounding concrete is stable. Widespread settlement, heaving, drainage problems, or base failure can make a larger replacement the better long-term scope.
We look at the crack pattern, movement, slope, drainage, base condition, edges, nearby structures, and how the surface is used. The cause matters more than the appearance of one crack.
Yes, when the failed area can be isolated and the surrounding slab remains serviceable. The section is laid out around clean cuts, joints, elevations, drainage, and a stable base before new concrete is placed.
New concrete usually differs from older concrete in color and weathering, especially at first. We aim for clean geometry, compatible texture, and sensible joint placement, but an invisible color match cannot be guaranteed.
Cost depends on demolition, access, concrete thickness, reinforcement, haul-off, base or drainage correction, replacement area, finish, and the transitions to concrete that remains. We provide a written estimate after the repair scope is defined.
It can be an option for a stable, sound slab with surface wear. Suitability depends on moisture, surface preparation, existing coatings, drainage, and the resurfacing system. We assess the condition before discussing options. Resurfacing does not repair an unstable base or stop ongoing heaving and settlement.
The options depend on whether the crack is stable, whether the slab has changed elevation, and how the floor is used. Isolated failed sections may be replaced while retaining sound concrete. Movement, repeated cracking, moisture, and planned vehicle or equipment loads need assessment before choosing a repair.
No. A surface filler does not restore lost support or correct water movement under the slab. If the concrete is settling, heaving, or separating at different elevations, the cause needs assessment before selecting crack treatment, section replacement, or a larger rebuild.
Send the project type, location, rough size, access notes, and timeline so the estimate starts with the right details.